- Description
Diamond Clear - Ultra High Gloss Urethane
"It's Time for your Floor to Shine!"DIAMOND CLEAR IS A NON-YELLOWING, ULTRA HIGH GLOSS CLEAR COATING - EXCELLENT FOR OUTDOOR SURFACES THAT WILL BE EXPOSED TO UV RAYS AS WELL AS HIGH TRAFFIC INDOOR AREAS
Coverage is approximately 300 square feet per gallon; 2 coats are strongly recommended for proper application.
Our Diamond Clear - High Gloss Urethane, is an industrial grade, clear coating that can be used on its own to enhance the look of any type of concrete, steel or wood surface where a high gloss coating is required. It can also be applied as a final clear "Topcoat" over almost any solvent-based paint for extra protection and shine.
Create a "Showplace" in your own home or business with a shiny high gloss finish that is simply outstanding.
Unlike other clear coatings that tend to yellow and break down over time, Diamond Clear is able to stand up to extreme weather conditions as well as the wear and tear of high traffic and heavy use. This is because of the quality of raw materials that are used in its formulation. Another quality that sets Diamond Clear apart from other paints is its diversity. It is ideal for use on many types of indoor and outdoor areas such as wood floors, outdoor patios and decks, offices, automobile showrooms, gymnasiums, warehouses, storage facilities, as well as on equipment, machinery and much more. Whether its used on its own or as a topcoat, the result is an easy to clean, durable and attractive gloss finish.
INDUSTRIAL GRADE ADVANCED RESIN TECHNOLOGY: Diamond Clear is a moisture cure urethane. Due to its "cross linking", high solids formulation it is designed specifically for maximum protection and long lasting quality.
ULTRA HIGH GLOSS FINISH: Diamond Clear can be used on its own over bare concrete, steel or wood surfaces or as a top coat over existing epoxy or oil based coatings.
COVERAGE: Approximate coverage is 300 square feet per gallon. Recommended thickness requires 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect less coverage on rough, porous or sandblasted surfaces.
To figure out the amount of paint you will require: Length x Width of surface = Square Footage x 2 (2 coats) divided by 300 Square Feet = gallons needed.
SUGGESTED USES: Excellent for outdoor surfaces that will be exposed to UV rays, high traffic indoor areas, or any type of wood or concrete where a high gloss clear coating is desired. Diamond Clear can also be used as a final "Topcoat" over almost any solvent-based paint or coating for extra protection and shine. Note: Diamond Clear is not intended for use over existing acrylic or water base coatings.
LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 40 degrees F or above 95 degrees F.
FINISH: High Gloss.
VEHICLE TYPE: Urethane.
SOLIDS BY WEIGHT: 75%.
WARRANTY: 10 Years.
AVERAGE DRY TIME: Dries to the touch in 12 hours. Second coat can be applied within 24-48 hours with no sanding required. Lower temperatures & higher humidity will slow down dry times
RECOMMENDED REDUCER: Product is intended to be used as packaged with no thinning required.
RESISTANCE TO: Chemicals, oil, grease, rust, corrosion, mildew, chipping and fading.
SURFACE PREPARATION: Concrete surface must be etched with a solution of 50% muriatic acid and 50% water. Clean surface area thoroughly with a bristle brush or broom and rinse thoroughly. Next clean the area with a mixture of TSP powder and water also using a bristle brush or broom. Rinse area thoroughly and allow to dry for 24 hours before applying the material. For wood or steel surfaces, clean the area with a mixture of TSP powder and water using a bristle brush or broom and allow the surface to dry for at least 24 hours before applying the material. Do not use muriatic acid on wood.
APPLICATION: Brush or roller. Rollers: Diamond Clear can be used on its own over bare concrete, steel or wood surfaces or as a top coat over existing epoxy or oil based coatings. Brush, Spray or Roller (Preferred). Rollers: 1/2" nap lambskin, mohair or phenolic roller. Keep roller wet. Roll in one direction, re-wet, then cross roll. Second coat can be applied after allowing the first coat a minimum of 24 hours to cure. Note: Diamond Clear is not intended for use over existing acrylic or water base coatings.
POT LIFE: 6 hours. Do not keep cover of container open during application. Only pour out enough material that will be used in 3-4 hours. Then close the cover immediately with the remaining product inside for future use.
SHELF LIFE: Maximum 12 Months
CLEAN UP: Xylene for equipment.
PACKAGE: 1 Gallon Can
