- Description
Platinum Plus - 2 Part Epoxy Pool Paint
Platinum Plus is our high quality, industrial grade 2-part epoxy pool paint.
Our Platinum Plus features a much higher solids by weight content than most other pool paints on the market today. And because of its solids content, along with the quality of the ingredients in its formulation, this is a self priming paint, there is no primer needed before application. It can be applied over most types of existing pool paints including acrylics, epoxy and rubber based coatings. It provides a beautiful finish that is easy to clean, very durable, and provides great protection against chalking, chlorine, automatic pool cleaning machines, algae & fading. It also offers a cost effective alternative to having to re-plaster your pool. Step up today and use the product that professionals trust!
Coverage is approximately 400 sq. ft. per 2 gallon kit. Two (2) coats are strongly recommended for proper application - No primer needed - this is a self priming epoxy pool paint
To figure out the amount of the 2-part epoxy paint required: Length of Pool x Width of Pool x 1.7 = square footage x 2 (2 coats) Divided by 400 = kits needed (remember that this product is sold in a 2 gallon kit)
- USED ON CONCRETE AND PLASTER
- ALSO FOR FIBERGLASS AND GUNITE
- CHLORINE AND SALTWATER RESISTANT
- STRONG UV PROTECTION
- PROVIDES A BRAND NEW UNIFORM FINISH
- CAN BE APPLIED OVER EXISTING PAINT
- 20 YEAR WARRANTY
SUGGESTED USES: Concrete, plaster, gunite, fiberglass pools, spas, fountains etc.
COLORS: White, Medium Blue, Aqua, Royal Blue, Sky Blue, Black
Now is the time to take a step up and use an industrial grade coating on your pool that is built to last!
SURFACE PREPARATION: Power wash or hose the surface to remove all loose paint, dirt, oils, suntan lotions and grease. Clean the pool with a mixture of Tri-Sodium Phosphate (TSP) and water, scrubbing the area thoroughly. Then etch with a solution of 50% muriatic acid and 50% water. Then clean the area again with TSP & flush with plenty of fresh water. Allow the surface to dry for at least 24 Hours. Glossy surfaces can be power sanded using 80 grit sandpaper if desired. After applying the 1st coat, allow it to dry for a minimum of 24 hours, then apply the 2nd coat and wait 5 days to refill the pool with water. If it should rain, add 1 extra day of curing time for every day of rain. That's it! You're done!!
VEHICLE TYPE: Epoxy Resin
SOLIDS BY WEIGHT: 90%
WEIGHT PER GALLON: 12 lbs. per gallon (varies by color)
RECOMMENDED DRY FILM: 20-22 mils (With Two Coats)
COVERAGE: Approximately 400 sq. ft. per 2 gallon kit. Less coverage will occur on bare, rough, or sandblasted surfaces. A minimum of 2 coats is highly recommended for proper protection, durability, and performance. Be sure to calculate this into your projected quantities needed to paint your pool surface before starting.
VISCOSITY AT 75°F (24°C): 120-140 KU (mixed). If you wish to thin the product for easier rollout performance, use 6-8 ounces of Xylene per 2 Gallon Kit. *Only if necessary.
AVERAGE DRY TIME: Dries to the touch in 12 hours. Lower temperatures & higher humidity will slow down drying times. Second coat can be applied with no sanding required after 24 hours. Allow for a minimum of 5 days of drying time to ensure the surface is completely cured before filling the pool with water. If it rains at any time during application, add 1 extra day of drying time for each day of rain.
WAIT 5 DAYS AFTER FINAL COAT BEFORE FILLING POOL WITH WATER.
RECOMMENDED REDUCER: If necessary, add 6-8 ounces of Xylene per 2 Gallon Kit for easier rollout performance.
RESISTANCE TO: Chlorine, Alkali, Algae, Mineral Oils, Fresh and Salt Water
RECOMMENDED PRIMERS: This is a self priming material.
APPLICATION: Brush, Spray, Roller (preferred)
ROLLERS: 1/2” or 1” nap lambskin, mohair or phenolic roller. Keep roller wet. Roll in one direction, re-wet, then cross roll.
SPRAY: Conventional Air 50 -70 psi, Tip Size .055-.070, Airless 2200- 2500 psi, Tip Size .019-.023.
LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 40°F or above 95°F. NOT FOR VINYL LINED POOLS.
SHELF LIFE: Maximum 12 months
MIXING: Mix both Part A & Part B individually for at least 5 minutes, and then mix the combined volumes (1:1 Mix Ratio) for at least 5 minutes. Allow mixed solution to rest for a maximum of 5-7 minutes and then begin using. Mix only what you expect to use in a 2-3 hour period.
POT LIFE: 2-3 hours at 75°F, 50% Humidity. Higher temperatures will substantially shorten the pot life. Only mix enough Part A (Base) and Part B (Activator) that you will use within a 2-3 hour time frame.
PACKAGE: 1 Gallon Cans (2 Gallons Per Kit)
