- Description
45% COPPER BOAT/MARINE BOTTOM PAINT W/ SCX- 1 GALLON
Given the highest rating by Powerboat Reports in CT testing - loaded with 45% copper, this multi-season ablative with booster SCX gives tremendous antifouling protection against barnacles, slime, grass & algae.
- SELF POLISHING
- SLIME CONTROL XTRA
- GOOD FOR MULTIPLE SEASONS
- NO HEAVY SANDING
- GREAT PROTECTION FOR MODERATE FOULING CONDITIONS
Covers approximately 300 square feet per gallon; 2 coats needed for proper application - 3rd coat recommended on the waterline
To figure out the amount of marine antifouling paint required: Length x Beam x .85 x 2 (2 coats)= Total / 300 feet = Gallons Required
Multi-Season Protection
The average boater who goes out on the water for 50-100 hours a year will get anti-fouling protection of 2-3 years
45% Copper Boat/Marine Antifouling Bottom Paint w/ SCX provides extended antifouling protection against barnacles, algae and hydroids in salt and fresh water on boat bottoms only. SCX - SLIME CONTROL XTRA - acts like a sunscreen to prevent slime and algae. Its ablative copolymer base renders a smooth finish with durability and abrasion resistance.
45% Copper Boat/Marine Bottom Paint w/ SCX releases biocide by the constant exposure of new paint film to the water. 45% Copper Boat/Marine Bottom Paint w/ SCX has universal application over all types of properly prepared bottom paints (except aluminum). For use on fast fiberglass boats, as well as wood and steel hulls, extended protection is possible, since performance is directly proportional to the amount of paint applied.
Surface Preparation
Surface must always be clean, dry and properly prepared prior to painting. Failure to do so will lead to eventually blistering and/or peeling. All sanded surfaces must be wiped clean with a dewaxer to remove sanding residue.
General Application
For use on boats below the true waterline. Can be brushed or rolled on fiberglass, wood, steel and previously painted surfaces per application systems below. Do not use on aluminum. Apply at least 2 coats for best performance, as the life of the paint is proportional to the number of coats applied.
Mixing and Thinning
Shake or mix thoroughly and stir continuously while using. Thin when necessary with Thinner.
Theoretical Coverage
Depending on surface conditions, one gallon of bottom paint will usually cover over 300 square feet of surface when brushed or rolled.
Clean Up
Use a Thinner for cleaning equipment and paint brushes.
Estimated Dry Times
Bottom paints are designed for overcoating after an overnight dry. Prior to launching, allow a minimum dry of overnight and a maximum of 60 days. If drying conditions are poor, or if paint was applied too thickly, longer periods of drying will be required. Fresh coats of paint must be thoroughly dry before overcoating.
Yearly Repainting
Scrub bottom clean at haul-out. Repaint only if old paint is sound and tight; if not, remove it by sanding or with paint remover. If old paint is rough, sand it with 100-150 grit sandpaper. Prepare seams, nicks and chips as below. Spotcoat any scuffs with antifoulant. Apply 2 coats of antifoulant.
On Bare Wood
If seams are not flush, fill them with seam compound. Dry several days until skin forms. Do not sand. Fill nicks with trowel cement, dry hard, sand, apply antifoulant (reduced 10%) then follow with 2 additional unreduced coats of antifoulant.
On Bare Fiberglass
Dewax by washing with a dewaxer, remove dissolved wax at once with clean paper towels or rags; repeat; sand hard to a dull finish with 80-100 grit sandpaper. Fill any chips with trowel cement, dry hard, sand. Apply 5 coats of our Bottom Protect High Build Epoxy Primer, then apply 2 coats of antifoulant.
On Bare Steel
Sandblast surface to a near white metal; remove blast residue with a broom and air hose. Wipe off with a dewaxer. Do not sand. Fill in any imperfections with fairing compound. Sand smooth and wipe clean. Apply 5 coats of our Bottom Protect High Build Epoxy Primer, then apply 2 coats of antifoulant.
PACKAGE:
1 Gallon can
See also:
HEAR WHAT SOME OF OUR HAPPY CUSTOMERS HAVE TO SAY...
"We re-coat the bottom of our sail boat every few seasons. We are very pleased to say your 45% Copper Boat/Marine Bottom Paint w/ SCXhas lasted much longer than expected. Your products are superb."
-Jack Easly
"I am a contractor and have used many of your paints and epoxy's. You have helped me many times choosing the right product for the right job. I like being able to talk to a live rep to get the answers I need when I need them."
-Jim Hardin
